Lpd3806-600bm-G5-24c Ab Two-Phase 5-24V 600 Pulses Incremental Optical Rotary Encoder

Type: LPD3806-600BM-G5-24C
Readout Model: Contact
Signal Output: Open Collector Output
Package: SMD
Brand: GTEACH
Trademark: GTEACH
Pulses: 600
Working Principle: Incremental
Operating System: Photoelectric
Installation Form: Axonia
Axonia: Synchronous Flange
Transport Package: 1 PCS Per Box
HS Code: 8543709990
Package Weight: 0.17kg (0.37lb.)
Package Size: 10cm x 8cm x 7cm 
1. Electrical specification:
(1) Resolution (P/R): 600
(2) Standard with 1.5M cable
(3) Operating voltage: DC5-24V
(3) Max Current Consumption: 40 mA
(4) Max Response Frequency: 30 KHz
(5) Maximum mechanical speed 5000 rev / min
(6) Integrated speed 2000 rev / min

Wiring: Green=A phase, white=B phase , red=Vcc positive supply, black=V0, please wiring as described above. Another metal shielding layer interference.
Uses: for measuring the rotational speed of the object, angle, acceleration, and length measurements.

Features: small size, light weight, easy installation, high cost performance.

Note: A phase and B-phase output lines must not be directly connected to VCC, otherwise, it will burn the triode.
 

1. Electrical specification:
 
(1) Resolution (P/R): 600
(2) Supply Voltage: DC 5V-24V
(3) Max Current Consumption: 40 mA
(4) Max Response Frequency: 30 KHz 
(5) Rise / Fall Time: 200ns (Line driver output), 1μ's
 
2. Mechanical specification:
(1) Starting torque: 1.5*10³ N.M
(2) Moment of inertia: 3.5*6 kgm²
(3) Shaft loading/Radial: 10N
(4) Thrust loading/Radial: 20N
(5) Max Allowable revolution: 2000rpm
(6) Net Weight: 100g
 
3. Environment:
(1)Ambient temperature -20 to 80 ºC
(2)Storage: -25 to 85ºC
(3)Ambient humidity: 30 - 85%
(4)Degree of Protection: IP50
(5)Vibration: 50m/s², 10-200HZ
(6)Shock:980m/s², 6ms
Caution for using
1.Installation
This unit consists of precision components. If you drop this unit, it may lose the function.
Please treat this product carefully.
When you install this unit, if eccentricity and deflection angle are larger, load is applied to the
Shaft It may shorten the life cycle of this unit.
Do not put strong impact with hammer, etc when insert coupling into shaft.

2.For using
Do not cut or connect circuit when power is ON.It may cause damage to the unit.
When the power source is Switching Power, it may cause surge. Install a surge absorber in
Power line. Wire should be shorter in order not to be influenced by noise.
Do not splash water, oil etc, cover the protecting hood when necessity.

3.Environment
Please do not use this unit with below environment, or it may cause malfunction.
Place where this unit or component may be damaged by strong vibration or impact.
Place where there is a lot of flammable or corrosive gases.
Place where strong magnet field or electric noise occurs.
Place where is beyond of the rated temperature or humidity.
Place where strong acids or alkali nearby.
Place where there is the direct ray of the sun.

4.Vibration and Impact
If a big impact or strong vibration applies to the product it may cause pulse errors.Be sure that
When installing this unit.
Encoder with high resolution can be easily affected by vibration, therefore tighten fixing bracket
When installing this unit.

5.Wire connection
Do not pull out the wire with over 30N strength after fixing the unit and wiring the cable.
If wire encoder cable with high voltage line or power cable in the same conduit, it may cause a
Malfunction or mechanical problem. Please wire it separately or use separated conduit.